Seals Material | ||||
Material | Code | Characteristic | Temperature (℃) | Application |
Polytetrafluoroethylene |
PTFE | Good chemical stability, high mechanical strength. Anti heat, cold, water, oil, pharmaceuticals, and other Mediums. Pressure 40MPa.Good wear resistance, low friction, self-lubrication. | -190~260 | Main material for wear rings, guide rings, back up rings,, and widely used in metallurgy, petrochemical, engineering machinery, light industrial machinery |
Nitrile Rubber | NBR | Anti oil, and heat. Good wear resistance. Widely used in the production of seal products, but not for phosphonate Series hydraulic oils and gear oils containing polar additives. | -40~120 | For the production of O-rings, oil seals, seal cups, and etc., suitable for general hydraulic and pneumatic systems as static seal or dynamic seal. |
Rubber and Plastics | RP | High elasticity, and high strength. Other characteristic are as same as NBR. | -30~100 | Material of O-rings,Y type rings, and wiper seals (dust rings). Mainly used in construction machinery and all kinds of high-pressure hydraulic systems. |
Nitrile Rubber + Cloth | NBR+Cloth | Complex by the NBR and cloth, high strength, wear resistance decreased slightly over NBR, other characteristic are as same as NBR. | -30~100 | Making cotton fabric seals for sealing construction machinery, metallurgical equipment, and various high-pressure systems. |
Viton | FKM | Anti heat, acid, chemicals, and oil (including phosphonate series of hydraulic oil), applies to all oil, gasoline, hydraulic oils, synthetic oils | -20~200 | Suitable for high temperature, chemical resistance, flame hydraulic oil seals. Widely used in metallurgy, electric power and other industries. |
Polyoxymethylene Delrin | POM | Oil, temperature, wear resistance, high compressive strength, good impact resistance, has good self-lubricating properties, good dimensional stability. | -40~120 | For the manufacture of the guide rings, back up rings. |
Phenolic Cloth | FQ | Oil, temperature, wear resistance, high compressive strength is 2-3 times than the thermoplastic material, better impact resistance, good dimensional stability | -50~130 | For the manufacture of the guide rings, the guide bushings. |
Polyurethane | TPU | Good mechanical properties, excellent wear resistance, excellent oil resistance. | -35~100 | For the manufacture of the high-pressure hydraulic seals. |
Material | Material Code | Measured Value of Material |
Applicable Seal Type |
Remarks | |||||
Hardness (Shore A) ±5 |
Tensile Strength (MPa) |
Eextensibility (%) |
Compression permanent deformation (%) |
Hardness change of hot air aging test (Point) |
Temperature range of use (℃) |
||||
Test conditions |
B:100℃ 24h/70h C:150℃ 24h/70h |
||||||||
Nitrile Rubber (NBR) | N800 (Black) | 80 | 22 | 315 | 14 | +6(B) | -35~120 | ORing, GK Seal | |
N801 (Black) |
80 | 22.5 | 340 | 18 | +6(B) | -35~120 | KDAS elastomer | ||
N802 (Black) |
80 | 22 | 320 | 14 | +6(B) | -35~120 | KZP, KA, KWK elastomer | ||
N900 (Black) |
90 | 22 | 240 | 28 | +4(B) | -35~120 | Wiper, U type ring, O ring | 90° hardness | |
NV700 (Black) |
70 | 17.5 | 380 | 18 | +5(B) | -35~120 | O ring, Combination Seal elastomer | Low temperature resistance | |
NV705 (Black) |
75 | 18 | 345 | 20 | +5(B) | -50~100 | |||
Viton (FKM) | F800 | 80 | 12 | 200 | 16 | +1(C) | -20~200 | O ring, Combination Seal elastomer | |
F801 | 80 | 12 | 200 | 14 | +1(C) | -20~200 | O ring | ||
F805 | 85 | 11.5 | 180 | 20 | +1(C) | -20~200 | U type ring, GK seal | ||
F900 | 90 | 15 | 160 | 22 | +1(C) | -20~200 | Wiper, U type ring and O ring | 90° hardness | |
Polyurethane (TPU) | P901 | 93 | 35 | 680 | 34 | +0(B) | -30~110 | Wiper | |
P902 | 92 | 28 | 800 | 30 | +0(B) | -35~110 | U type seal | ||
P903 | 93 | 38 | 740 | 30 | +0(B) | -30~115 | Wiper | ||
P904 | 93 | 35 | 800 | 38 | +0(B) | -30~110 | Wiper, U type seal | ||
P905 | 95 | 46 | 540 | 32 | +0(B) | -30~110 | KZP, KKR, turning seal | ||
P906 | 95 | 46 | 540 | 32 | +0(B) | -30~100 | Hydrolysis resistant sealing | ||
P908 | 98 | 50 | 480 | - | +0(B) | -30~100 | KZP, KKR, TUP material GS seal | ||
PV902 | 92 | 28 | 820 | 30 | +0(B) | -40~100 | U type ring | Low temperature resistance |
Material | Material Code | Measured Value of Material |
Applicable Seal Type |
Remarks | |||||
Hardness (Shore D) ±5 |
Tensile Strength (MPa) |
Eextensibility (%) |
Compressive strength MPa(N/mm2) |
Temperature range of use (℃) |
|||||
2.5% deformation |
10% deformation |
||||||||
PTFE | T600(White) | 62 | 17 | 320 | 14 | 20.4 | -190~260 | Back Up Ring | |
T605(Brown) | 64 | 21.2 | 280 | 18 | 25 | GS,KG, Wiper, Rotary Seal | |||
T601(Brown) | 64 | 21.2 | 280 | 18 | 26 | Anti fouling ring、Guide elements | |||
POM | S805(Black) | 82 | 65.6 | - | 90 | 116 | -40~110 | KDAS L ring, Guide Ring, Back Up ring | |
S801(White) | 82 | 65.6 | - | 90 | 116 | Back Up Ring | |||
S802(Red Brown) | 82 | 70 | - | 96 | 122 | Guide Ring | |||
S803(Brassy) | 82 | 70 | - | 96 | 122 | Guide Ring | |||
Polyamide | M700(Blue) | 71 | 80 | - | 48 | 72 | -50~120 | KDAS Back Up Ring | |
M701(Black) | 86 | 98 | - | 90 | 120 | -50~120 | KZP,KA Back Up Ring | ||
M702(Black) | 88 | 102 | - | 130 | 170 | -50~130 | KWK Slip Ring | ||
Phenolic Cloth | QJ900(Yellow) | 92(HRM) | 48 | - | 190 | 280 | -50~130 | Guide Ring | |
QJ901(Yellow) | 96(HRM) | 60 | - | 190 | 300 broken | Guide Ring | |||
QJ902(Blue) | 92(HRM) | 48 | - | 160 | 252 broken | Guide Ring | |||
Nitrile Rubber + Cloth | BN500(Black) | / | / | / | / | / | / | V Type Combination Seal |